| Customization: | Available |
|---|---|
| Application: | Motor, Motorcycle, Machinery, Agricultural Machinery, Car |
| Hardness: | Hardened Tooth Surface |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Feature
1.High modular design, with independent intellectual property rights.
2.German worm gears are used to handle worm gears.
3.Through special gear geometry, it has high torque, high efficiency and long life cycle.
4.It can realize the direct combination of two sets of gearboxes.
5.Installation method: foot installation, flange installation, torque arm installation.
6.Output shaft: solid shaft, hollow shaft.
Application
1.Chemical and Environmental Protection
2.Metal Processing
3.Building Construction
4.Agriculture and Food
5.Textile and Leather
6.Forest and Paper
7.Car Wash Machinery
|
shell material |
Cast Iron / Ductile Iron |
|
shell hardness |
HBS190-240 |
|
gear material |
20crmnti alloy steel |
|
Gear Surface Hardness |
HRC58°~62° |
|
Gear Core Hardness |
HRC33~40 |
|
Input/Output Shaft Material |
42crmo alloy steel |
|
Input/Output Shaft Hardness |
HRC25~30 |
|
Gear machining accuracy |
Precision grinding, grade 6~5 |
|
lubricating oil |
GB L-CKC220-460, shell withstand voltage 220-460 |
|
heat treatment |
Tempering, bonding, quenching, etc. |
|
effectiveness |
94%~96% (depending on transmission stage) |
|
noise (maximum) |
60~68dB. |
|
Temperature rise (maximum) |
40ºC |
|
Temperature rise (oil) (maximum) |
50ºC |
|
vibration |
≤20.μm. |
|
cringe |
≤20arcmin. |
|
Bearing brand |
Chinese brand bearings, HRB / LYC / ZWZ / C&U. or other brand requirements, SKF, FAG, INA, NSK |
|
Oil seal brand |
NAK --- Taiwan or other brand requirements |
K series reducer has the following models:
K37 K47 K57 K67 K77 K87 K97 K107 K127 K157 K167 K187
KA37 KA47 KA57 KA67 KA77 KA87 KA97 KA107 KA127 KA157 KA167 KA187
KF37 KF47 KF57 KF67 KF77 KF87 KF97 KF107 KF127 KF157 KF167 KF187
KAF37 KAF47 KAF57 KAF67 KAF77 KAF87 KAF97 KAF107 KAF127 KAF157 KAF167 KAF187
KAZ37 KAZ47 KAZ57 KAZ67 KAZ77 KAZ87 KAZ97 KAZ107 KAZ127 KAZ157 KAZ167 KAZ187
KAT37 KAT47 KAT57 KAT67 KAT77 KAT87 KAT97 KAT107 KAT127 KAT157 KAT167 KAT187
KAB37 KAB47 KAB57 KAB67 KAB77 KAB87 KAB97 KAB107 KAB127 KAB157 KAB167 KAB187
1. Body / Box Body
(1) The section of the cover and the body shall be smooth and smooth to ensure tight assembly. Check the contact tightness of the section, that is, the insertion depth of the plug ruler less than 0.05mm shall not be greater than 1 / 3 of the section.
(2) The upper cover and the body shall not crack, and the kerosene inspection shall not contain leakage.
2. Dute Line Cylindrical Gear
(1) The gear shall not have defects in burrs, cracks, fractures, etc.
(2) gear engagement that the tooth height and tooth width is not greater than 20%.
(3) gear must be correctly engaged after assembly and its contact area shall meet the provisions in Table 1.
(4) The side clearance of gear engagement shall meet specified in Table 2.
(5) The top gap of the gear engagement is 0.2~0.3m (m is the normal modulus).
(6) Check the side and top clearance of the gear by pressure lead method and if not in accordance with Articles (4) and (5), the center distance may be corrected in Table 2 and (5)
(7) The center distance limit deviation of both gears shall meet the provisions in Table 3.
(8)The parallelism of the gear centerline on the tooth width is not greater than that specified in Table 4
(9)The radial beat of the gear rim shall not be greater than that specified in Table 5
(10)The maximum allowable wear value of tooth thickness at the gear section circle shall meet Table 6.
3. Bevel Gear Wheel
(1) The gear must be smooth without burrs, scars, cracks, etc.
(2) The limit deviation of the clip angle of the gear shaft is specified in Table 7.
(3) The displacement of gear centerline shall not be greater than specified in Table 8 and the displacement inspection method is shown in FIG. 4.
(4) The side gap of gear engagement shall meet the provisions in Table 9
(5) Top gap of gear engagement is 0.2~0.3m.(The m is the large-end module number)
(6) The displacement of the gear cone shall not be greater than that specified in Table 10
Ocheng machinery equipment is subcompany of China YanFeng group ,which was found in 1987 .The company'existing plant area is 60000 square meters.It has advanced experimental test equipment and production line in the industry,In recent years,it has spent 30 million yuan to purchase more than 30 high-precision CNC machine tools,more than 200 various types of machine tools ,and fixed assets of more than 500 million yuan.
We specializing in R & D and manufacturing of various gear reducers, different types of chillers, film blowing machines, bag making machines, bubble film machines, printing machines, recycling machines ,motorcycle accessories and other machine assembly parts etc.we have got certificate such as ISO9001 and etc ,Who provide professional NON-STANDARD products with complete design and customization to satisfy your requirement.
We has gathered a batch of outstanding professional team with more than 10 years' experience in this industry. Adopting brand-new modulation, the productions of our company are featured by short delivery time, high performance and more stable operation.
Our products sell well all over the country and are exported to Southeast Asia, the Middle East, Central Asia, Russia, Europe, South America, North America, Africa, dozens of countries and regions, winning a good market response and customer reputation.
We pay close attention to internal management, after-sales service, scientific and technological progress and information. We continue to grow and develop at the same time.
A:We will respond to you within 12 hours of the working day.
){kind=link}